FAQ Main Index Page Contact Us:EMail Call Us:(302) 629-8508
Related Items On Sale Mounting Hardware And Kits


Oldsmobile retractable combination lap seat belts with shoulder harness retrofit conversion kits available for use when originality is not required. A retrofit conversion kit includes the required mounting hardware along with installation instructions to upgrade from a non retractable or retractable lap seat belt only or to replace a damaged factory retractable lap seat belt with independent shoulder harness or to add a retractable lap seat belt with shoulder harness in a vehicle that did not previously have retractabe lap seat belts with shoulder harness installed. Retrofit conversions kits are available for bench seat and bucket seats. All seat belts and hardware are new with all seat belts manufactured or assembled in the USA with USA certification tag confirming compliance with current FMVSS(Federal Motor Vehicle Safety Standards) 209 and 302.

Important Installation Information; (Click On Picture To Enlarge)Most vehicles manufactured after 1965 have factory upper shoulder harness bracket mounting hole or holes located on the lower roof panel or pillar post which would be threaded or have a threaded reinforcement plate or nuts welded behind the hhole(s) between the body inner and outer steel panel. Our retrofit conversion kits include threaded reinforcement plates to be used when the hole(s) are not threaded or reinforced or to be used when the upper shoulder harness bracket mounting point does not exist which is required for the installation.






For Use In The Vehicles Listed Below

To Be Installed In A Coupe Or Hardtop Only
Cutlass: 1964-75
Cutlass Supreme: 1965-75
F85: 1964-75
Vista Criuser: 1964-72


Quantity:

Quantity:

Quantity:
Quantity:

Product Notes: Click On Picture To Enlarge
Available with black webbing only
  • Includes: Seat belts and installation hardware for the driver and passenger with installation instructions.
  • Buckle: Metal. Measures 1 7/8" x 1 7/8" with GM Mark Of Excellence on the press area.
  • Manufactured under GM reproduction license.
  • Center/Rear Seat Belt Length 60": Adjustable buckle side 36". Fixed latch side 24".
  • Center/Rear Seat Belt Length 74": Adjustable buckle side 40". Fixed latch side 34".
  • For product questions or ordering assistance call (302)629-8508.

    Rear Seat Mounting Hardware
    A retrofit mounting kit which includes threaded underbody reinforcing plates to add support to the mounting points should be used when seat belts are being installed in a location were they were not previously dealer or factory installed. Standard mounting kit is not required when ordering.
    MH2 Standard Mounting Kit: Includes yellow zinc bolts, washers, nuts and oversize underbody reinforcing washers.
    MH4 Standard Mounting kit: Includes zinc chromate bolts, washers, nuts and and oversize underbody reinforcing washers.
    201K Retrofit Mounting Kit: Includes yellow zinc bolts, washers plus threaded underbody reinforcing plates.

  • FAQ Main Index Page Contact Us:EMail Call Us:(302) 629-8508
    Related Items On Sale Mounting Hardware And Kits



    Liability Disclaimer: The Andover Companies, and its subsidiaries assumes no responsibility for any damage due to the installation, either proper or improper, or for any damage or bodily injury arising from the use of any product. It is understood that the purchaser, installer and/or end user is responsible for the determination that the product purchased is suitable for its intended use and agrees to indemnify and hold The Andover Companies,Inc and its subsidiaries, harmless for any claim, action or demand arising from the installation and/or use of any product. There are no guarantees or warrantees on any product, implied or expressed, of fitness for a particular use with any such warrantees being specifically and expressly disclaimed. In the event any of the above limitations are held not enforceable our liability shall not exceed an amount equal to the amount paid to us for the product. Receipt of product or products confirm acceptance of disclaimer and liability transfer to purchaser, installer and/or end user.

    All information detailed within this document is based on information believed to be accurate but accuracy is not guaranteed. All pictures, diagrams and item descriptions are protected property of The Andover Companies,Inc and are not to be duplicated in any manner without written permission.

    (ARW23 10-12-19)